Search found 628 matches

by icelikkilinc
Thu Jul 18, 2019 7:51 pm
Forum: Anything else and for sale. . .
Topic: “The Beast”
Replies: 81
Views: 1548

Re: “The Beast”

Richard
Found this site over UK

https://www.aquasealrubber.co.uk/produc ... atch-seal/

Quite a selection of products and custom options as well.
by icelikkilinc
Tue Jul 16, 2019 8:25 am
Forum: Builder's Power Boats
Topic: ST21 Hybrid Powered "SKINNYDIP" Noosa Australia
Replies: 4455
Views: 243025

Re: ST21 Hybrid Powered "SKINNYDIP" Noosa Australia

agree with cape man

Michael, I know the tiller is temp one on the pic. Will you be using the same type of wood for donut and tiller?
hopefully the same with grain and color to match :wink:
by icelikkilinc
Mon Jul 15, 2019 6:44 am
Forum: Anything else and for sale. . .
Topic: “The Beast”
Replies: 81
Views: 1548

Re: Cape Sable Cooler

Aripeka Angler wrote:
Sat Jul 13, 2019 3:35 pm
cape man wrote:
Sat Jul 13, 2019 6:39 am
I ran some numbers on the required insulation.
I wonder if the prop guy uses the same formula? :lol:
:lol: :lol: :lol: :lol:

Looking great Richard. Hope CG does not stop you on the way to Bahamas for human trafficking :D
by icelikkilinc
Sun Jul 14, 2019 6:45 am
Forum: Builder's Power Boats
Topic: ST21 Hybrid Powered "SKINNYDIP" Noosa Australia
Replies: 4455
Views: 243025

Re: ST21 Hybrid Powered "SKINNYDIP" Noosa Australia

http://gallery.bateau2.com/displayimage.php?pid=71921&fullsize=1 Michael looking great. Donut pad might look good from distance proportionally but seems a little clunky in close up If you would reduce the height flush to white ply as I tried to point, Would it have enough meat to accommodate the str...
by icelikkilinc
Wed Jul 10, 2019 2:48 am
Forum: Anything else and for sale. . .
Topic: Angle irons and such.
Replies: 9
Views: 217

Re: Angle irons and such.

Are you able to install another angle iron as cross member, approximately from where the ladder is to the other hull? Looks as you only have 1 directional load bearing on the middle which might be the reason of bend. if you were to install 1 as cross, you will have 4 small rectangular areas created ...
by icelikkilinc
Sat Jul 06, 2019 2:29 pm
Forum: Builder's Power Boats
Topic: ST21 Hybrid Powered "SKINNYDIP" Noosa Australia
Replies: 4455
Views: 243025

Re: ST21 Hybrid Powered "SKINNYDIP" Noosa Australia

glossieblack wrote:
Sat Jul 06, 2019 3:39 am

Image
Beauty :D
by icelikkilinc
Wed Jun 19, 2019 4:21 am
Forum: Power Boats
Topic: Is my boat falling apart?
Replies: 25
Views: 956

Re: Is my boat falling apart?

https://forums.bateau2.com/download/file.php?id=10763&t=1 On this pic, it seems as you might have access for rework. I would seal the ply first, and than probably put a long piece of wood between frames to distribute the load. should act as butt block at the bottom of the seam as well. I don't have...
by icelikkilinc
Wed Jun 19, 2019 4:08 am
Forum: Builder's Power Boats
Topic: ST21 Hybrid Powered "SKINNYDIP" Noosa Australia
Replies: 4455
Views: 243025

Re: ST21 Hybrid Powered "SKINNYDIP" Noosa Australia

slow and steady wins the race :wink:
by icelikkilinc
Wed Jun 12, 2019 9:51 am
Forum: Builder's Power Boats
Topic: Mike Smith's TW28 build
Replies: 144
Views: 4424

Re: Mike Smith's TW28 build

Nice cigar :wink: I used a circular saw set at 8 mm for the 12mm panel. around 2 inches gap, and if I recall correctly approximately stopped 6 inches before the bow. after the hull shape was set and outside glass complete, prior to flip, I crawled under and tried to fill with thickened epoxy where a...