Search found 2902 matches

by Fuzz
Fri Feb 23, 2018 1:26 am
Forum: Cracker Larry's Corner: Boat Repair and Rebuild Support
Topic: XF20 transom rebuild
Replies: 52
Views: 907

Re: XF20 transom rebuild

Man I sure do not envy you working overhead. I am sure you are happy that part is done.
by Fuzz
Fri Feb 23, 2018 1:16 am
Forum: Resins, Fiberglass and Paint
Topic: 1969 Boston Whaler restoration - paint, though
Replies: 14
Views: 309

Re: 1969 Boston Whaler restoration - paint, though

Love that picture :D
Typical boat builder when things are just a little off :lol:
by Fuzz
Thu Feb 22, 2018 2:29 pm
Forum: Builder's Small Boats
Topic: D5 Build
Replies: 102
Views: 2039

Re: D5 Build

With as much V as there is in the bottom I would think you do not need a skeg. What do the plans say? It might be needed to help stiffen the bottom and if that is the case then yes you need it.
by Fuzz
Thu Feb 22, 2018 2:23 pm
Forum: Power Boats
Topic: Alan's C17
Replies: 74
Views: 1303

Re: Alan's C17

Alan I am pretty sure the picture is showing the lower panel installed and the upper is yet to come. In the picture you can see where the frames extend on down for the upper panels.
by Fuzz
Thu Feb 22, 2018 3:57 am
Forum: Builder's Power Boats
Topic: Wouter's PH18 Namibia
Replies: 422
Views: 25432

Re: Wouter's PH18 Namibia

That is one fine looking boat right there :!: I bet you are getting pumped for the launch.
by Fuzz
Thu Feb 22, 2018 3:39 am
Forum: Anything else and for sale. . .
Topic: GF12 FOR SALE
Replies: 9
Views: 336

Re: GF12 FOR SALE

AA do you think it could go as extra luggage :lol:
My buddy Dan was talking about wanting a hard bottom skiff for his Californian. Too bad the boat is not 4000 miles closer. I may end up building him a GV at some point.
by Fuzz
Thu Feb 22, 2018 3:31 am
Forum: Cracker Larry's Corner: Boat Repair and Rebuild Support
Topic: Sintes 21 Rebuild
Replies: 954
Views: 30690

Re: Sintes 21 Rebuild

I have to say having a work bench/storage area is a huge help. If I had a little more room I would build a rolling bench to keep along the side. Got tired of looking at the same thing every day so I laid a little primer on part of the cabin and bow today. I am sure it will show me places that need m...
by Fuzz
Wed Feb 21, 2018 3:13 am
Forum: Builder's Power Boats
Topic: ST21 Hybrid Powered "SKINNYDIP" Noosa Australia
Replies: 2307
Views: 119375

Re: ST21 Hybrid Powered "SKINNYDIP" Noosa Australia

I am watching and waiting for what you do for the anchor. And there is a better than even chance I will copy you without the least little bit of shame :wink:
by Fuzz
Wed Feb 21, 2018 3:10 am
Forum: Builder's Small Boats
Topic: D5 Build
Replies: 102
Views: 2039

Re: D5 Build

Yep. There some friendly and knowledgeable people over there. The problem is you have to sort through a ton of keyboard cowboys to find them. Keeping the clowns sorted out on this forum is one of the things that make it so enjoyable to be a part of :wink: So are you messing with the FS any or just c...
by Fuzz
Wed Feb 21, 2018 3:01 am
Forum: Cracker Larry's Corner: Boat Repair and Rebuild Support
Topic: Sintes 21 Rebuild
Replies: 954
Views: 30690

Re: Sintes 21 Rebuild

glossieblack wrote:
Wed Feb 21, 2018 1:57 am
Nice workbench you've added to her transom. :lol:
I keep hoping that at some point it will have other uses but I have my doubts at times. The part of building where you see no major changes at the end of the day is tough. But I try to remember what the Cracker said about one bite at a time.