Search found 16 matches

by 3rdday
Sun Mar 23, 2008 9:35 am
Forum: Cracker Larry's Corner: Boat Repair and Rebuild Support
Topic: Classic 21 Seacraft Restoration
Replies: 35
Views: 8897

http://i233.photobucket.com/albums/ee58/bscapo1/FGCloth.jpg Here is a Pic of the cloth, i have a huge roll of this, I also have a huge roll of Plain FG mat. If you dont thinh the cloth can be used, would you consider a trade/ or partial trade of the cloth and the Mat for the stuff you might reccome...
by 3rdday
Thu Mar 13, 2008 10:56 pm
Forum: Cracker Larry's Corner: Boat Repair and Rebuild Support
Topic: Classic 21 Seacraft Restoration
Replies: 35
Views: 8897

What, no answer! I want to spend $$ with you. I do appreciate the help thus far.
by 3rdday
Tue Mar 11, 2008 9:16 pm
Forum: Cracker Larry's Corner: Boat Repair and Rebuild Support
Topic: Classic 21 Seacraft Restoration
Replies: 35
Views: 8897

I wasn't expecting it to be that expensive, I was expecting about 2K. I estimated, 15 Gal epoxy,6 sheets h80, 1 sheet renicell, some FG tape, cabosil and the glass i already have.I prefer to go the composite route, I don't want to have to do this again, I want to do the work once and thats it. I can...
by 3rdday
Fri Mar 07, 2008 9:01 pm
Forum: Cracker Larry's Corner: Boat Repair and Rebuild Support
Topic: Classic 21 Seacraft Restoration
Replies: 35
Views: 8897

That Pic. is what I am looking for, I looked at the waterline measured the bracket heights based on the 25" shaft engine and compensated bracket height (raise approx. 1" per 1 ft of setback) based on setback, looked at the floor and measured the transom, to the floor. The thru bolts will end up just...
by 3rdday
Fri Mar 07, 2008 2:20 pm
Forum: Cracker Larry's Corner: Boat Repair and Rebuild Support
Topic: Classic 21 Seacraft Restoration
Replies: 35
Views: 8897

http://www.hermco.net/images/bid0009.jpg http://www.hermco.net/images/bid0001.jpg http://www.hermco.net/images/Graham%2020'/GSC0019.jpg http://www.hermco.net/images/Graham%2020'/GSC0028.jpg What you are saying about the bulkhead makes allot of sense, If there are other options with close or equal st...
by 3rdday
Fri Mar 07, 2008 11:22 am
Forum: Cracker Larry's Corner: Boat Repair and Rebuild Support
Topic: Classic 21 Seacraft Restoration
Replies: 35
Views: 8897

I have no examples, There are only 5 known in existence. thay all had inboards except the ones that Carl Moesly raced. he modified the stock boats. I will call you.
by 3rdday
Thu Mar 06, 2008 10:06 pm
Forum: Cracker Larry's Corner: Boat Repair and Rebuild Support
Topic: Classic 21 Seacraft Restoration
Replies: 35
Views: 8897

From what you said, I will be rotating the cloth every other layer? The extra epoxy does not bother me, would rather overbuild, I plan on keeping the boat a lifetime. Your question about the bulkhead I am assuming is; am I going to go with a full bulkhead just in front of the transom. I prefer not t...
by 3rdday
Wed Mar 05, 2008 11:37 am
Forum: Cracker Larry's Corner: Boat Repair and Rebuild Support
Topic: Aquasport Rebuild - Classic "Flatback"
Replies: 325
Views: 216067

gk108 wrote:Twin Homelite 55's :!:
They put twin homelite 55s on the 21 seacraft also! johnson & Kirby sold lots of Em in Miami.
by 3rdday
Wed Mar 05, 2008 8:28 am
Forum: Cracker Larry's Corner: Boat Repair and Rebuild Support
Topic: Classic 21 Seacraft Restoration
Replies: 35
Views: 8897

I will not using the mat..My mistake, I meant F.G. cloth. I want to use the 24 oz Fiberglass Cloth, no mat backing, just stiched / weaved glass. There will be one engine, not two. in an earlier post you had engines-plural, just wanted to clarify. i know you are making many recomendations for many bo...
by 3rdday
Tue Mar 04, 2008 9:43 pm
Forum: Cracker Larry's Corner: Boat Repair and Rebuild Support
Topic: Classic 21 Seacraft Restoration
Replies: 35
Views: 8897

I believe I may end up replacing the stringers, perhaps Divinicell??? If so which model, the H80 1/2".? I am open to a bulkhead just in front of the transom, does it have to be full? I could use that space for batteries,Fuel water seperator, battery switches etc, but would obviously need access thru...