Search found 323 matches

by FluidDynamic
Sun Jun 07, 2020 5:17 pm
Forum: Power Boats
Topic: Panga 20 Build
Replies: 692
Views: 64652

Re: Panga 20 Build

First coat of bilgecoat. A few more to go.
by FluidDynamic
Sat Jun 06, 2020 11:48 pm
Forum: Power Boats
Topic: Panga 20 Build
Replies: 692
Views: 64652

Re: Panga 20 Build

Finished my bilge. Ready to sand and paint. Then ill install the fuel water seperatorand put the motorwell floor in.
by FluidDynamic
Sat Jun 06, 2020 11:25 pm
Forum: Power Boats
Topic: Panga 20 Build
Replies: 692
Views: 64652

Re: Panga 20 Build

I think I've settled on the white suzuki 60 hp. If you read jasmine's thread he said a 50 would even be OK. There are alot of charter boats in my area running suzukis. My other boat i have 300 verados and love them. I've had Yamaha, mercury, and suzukis. All three have been great motors. Maybe, I've...
by FluidDynamic
Thu Jun 04, 2020 11:17 pm
Forum: Power Boats
Topic: Panga 20 Build
Replies: 692
Views: 64652

Re: Panga 20 Build

The small stuff is the most time consuming. Cut the electrical tube down in the rear port locker. I then placed cleats and the sole. Once cured, I will cut the hole over the flushed electrical tube where the engine harness can be run. I have also finished taping all the sole joints. Left a hole for ...
by FluidDynamic
Thu Jun 04, 2020 10:53 pm
Forum: Builder's Power Boats
Topic: Sharkbait PG20
Replies: 113
Views: 3459

Re: Sharkbait PG20

Even though your putting the wide cloth on, I would still put tape on those butt joints. It's on the plans where it says "The fiberglass splices are made of one layer of biaxial each side". Just don't wont you to have a week spot.
by FluidDynamic
Thu Jun 04, 2020 7:59 pm
Forum: Builder's Power Boats
Topic: Sharkbait PG20
Replies: 113
Views: 3459

Re: Sharkbait PG20

Well that was quick. I probably looked at mine for 3 weeks before I flipped it. The race is on. I'm impressed you made those bends on the bottom panels without kerfing. Did you put fiberglass over the butt joints on the panels? I don't see them.
by FluidDynamic
Wed Jun 03, 2020 10:40 pm
Forum: Builder's Power Boats
Topic: Sharkbait PG20
Replies: 113
Views: 3459

Re: Sharkbait PG20

Agree, left a few pinholes as well. Im at the stage where there is a bunch of tiny things to do. Hopefully I can start putting the gunnel cap and frames on soon.
by FluidDynamic
Wed Jun 03, 2020 5:08 pm
Forum: Builder's Power Boats
Topic: Sharkbait PG20
Replies: 113
Views: 3459

Re: Sharkbait PG20

Alot faster than I am. Looks great.
by FluidDynamic
Fri May 29, 2020 2:36 pm
Forum: Builder's Power Boats
Topic: Sharkbait PG20
Replies: 113
Views: 3459

Re: Sharkbait PG20

I'd be lucky to get one panel sanded in a day.
by FluidDynamic
Fri May 29, 2020 2:14 pm
Forum: Power Boats
Topic: Panga 20 Build
Replies: 692
Views: 64652

Re: Panga 20 Build

Its a festool ro150 rotex. Yes I prefer the festool paper.