Search found 345 matches

by FluidDynamic
Fri Jan 04, 2019 8:41 pm
Forum: Power Boats
Topic: Panga 20 Build
Replies: 746
Views: 76618

Re: Panga 20 Build

Never built a boat before so I didn't really know what the point was. I see now. Thanks. I have the plywood, but not the epoxy yet. It was supposed to come today, but I saw the ups truck drive right by. I know I've read not to use patterns to cut out the plywood, but I use microstation on a daily ba...
by FluidDynamic
Fri Jan 04, 2019 7:10 pm
Forum: Power Boats
Topic: Panga 20 Build
Replies: 746
Views: 76618

Re: Panga 20 Build

What is the point of placing the stringers on now if I'm going to remove all of the frames when it's flipped?
by FluidDynamic
Fri Jan 04, 2019 4:40 pm
Forum: Power Boats
Topic: Panga 20 Build
Replies: 746
Views: 76618

Re: Panga 20 Build

No issues with the plywood. No issues with delivery.
by FluidDynamic
Fri Jan 04, 2019 3:26 pm
Forum: Power Boats
Topic: Panga 20 Build
Replies: 746
Views: 76618

Re: Panga 20 Build

Plywood looks good.
by FluidDynamic
Fri Jan 04, 2019 3:24 pm
Forum: Power Boats
Topic: Panga 20 Build
Replies: 746
Views: 76618

Re: Panga 20 Build

Thanks for the replies. I finally got frame D placed and will be putting E up tonight. I also received my plywood today. The curb side delivery was tough when I had to open the box at the curb and carry each piece by myself up a hill and into the garage. Finally, I am ready to start cutting some ply...
by FluidDynamic
Wed Jan 02, 2019 11:47 pm
Forum: Power Boats
Topic: Panga 20 Build
Replies: 746
Views: 76618

Re: Panga 20 Build

I was going to put Frame D on tonight, but ran out of screws. I have question on the deck. I would like to finish the top of the deck so I can epoxy and varnish it. The plans call for 1 layer of biaxial tape at the seams. If I place biaxial on the top of the deck, won't this show through the epoxy. ...
by FluidDynamic
Tue Jan 01, 2019 11:38 pm
Forum: Power Boats
Topic: Panga 20 Build
Replies: 746
Views: 76618

Re: Panga 20 Build

I've been reading Jasmine and Dynamos panga 20 builds and have a question about bending the bottom around the frames. It looks like they used Meranti for there bottom panels. If I'm using Okoume, will I have as much trouble as they did?
by FluidDynamic
Tue Jan 01, 2019 4:45 pm
Forum: Power Boats
Topic: Panga 20 Build
Replies: 746
Views: 76618

Re: Panga 20 Build

FluidDynamic wrote:
Tue Jan 01, 2019 12:28 pm
They are ramset nails that were shot into the concrete. Should anchor with boots instead?
by FluidDynamic
Tue Jan 01, 2019 1:37 pm
Forum: Power Boats
Topic: Panga 20 Build
Replies: 746
Views: 76618

Re: Panga 20 Build

FluidDynamic wrote:
Tue Jan 01, 2019 12:28 pm
They are ramset nails that were shot into the ground. Should anchor with bolts instead?
by FluidDynamic
Tue Jan 01, 2019 12:28 pm
Forum: Power Boats
Topic: Panga 20 Build
Replies: 746
Views: 76618

Re: Panga 20 Build

They are ramset nails that were shot into the concrete. Should anchor with bolts instead?