Corsair 13 in Metairie LA

Boats up to 15' for oars, power or sail. Please include the boat type in your question.
Marshall Moser
Active Poster
Active Poster
Posts: 392
Joined: Mon Aug 02, 2010 3:00 pm
Location: Siler City, NC

Re: Corsair 13 in Metairie LA

Post by Marshall Moser » Mon Sep 30, 2019 8:46 am

plenty of builders add hardware after paint, you just have to drill, fill, and re-drill any holes to make sure there isn't exposed wood.



Jaysen
* Bateau Builder *
* Bateau Builder *
Posts: 4259
Joined: Wed Aug 05, 2015 7:59 am
Location: St Helena Island, SC

Re: Corsair 13 in Metairie LA

Post by Jaysen » Mon Sep 30, 2019 11:56 am

I did... Next build i will do it before paint. Why? Because I wound up with "epoxy goop" all over the place. Sure i'm sloppy. But drips happen. So does stuff running out of the hole (even though it was super thick). then you have to sand all that crap off when means you have to paint it. Then you have blotchy paint since some is faded from use and some it fresh.

Or just don't be messy and be better at sanding than I am.
Jaysen wrote:
Mon Apr 29, 2019 3:44 pm
I tried to say something but God thought I was wrong and filled my mouth with saltwater. I kept my pie hole shut after that.

Jarret.brashear
Frequent Poster
Frequent Poster
Posts: 13
Joined: Sat Aug 17, 2019 12:10 am
Location: Louisiana

Re: Corsair 13 in Metairie LA

Post by Jarret.brashear » Sun Dec 01, 2019 8:15 pm

Exactly what part should I use as a stemhead fitting and how does it attach?

Jarret.brashear
Frequent Poster
Frequent Poster
Posts: 13
Joined: Sat Aug 17, 2019 12:10 am
Location: Louisiana

Re: Corsair 13 in Metairie LA

Post by Jarret.brashear » Sun Dec 08, 2019 1:37 pm

Anybody know where I can find this Ronstan RF292 wingnut pivot for the rudder? Or something comparable? Nothing comes up on Ronstans webside or anywhere else

Jarret.brashear
Frequent Poster
Frequent Poster
Posts: 13
Joined: Sat Aug 17, 2019 12:10 am
Location: Louisiana

Re: Corsair 13 in Metairie LA

Post by Jarret.brashear » Sun Dec 08, 2019 2:07 pm

I cant find anything called a Delrin sleeve that even approaches the diameter that I would need for the mast partner. Is this called something else?

User avatar
pee wee
Very Active Poster
Very Active Poster
Posts: 1696
Joined: Sun May 01, 2011 8:29 am
Location: Georgia

Re: Corsair 13 in Metairie LA

Post by pee wee » Mon Dec 09, 2019 8:58 am

Jarret.brashear wrote:
Sun Dec 08, 2019 2:07 pm
I cant find anything called a Delrin sleeve that even approaches the diameter that I would need for the mast partner. Is this called something else?
No idea what size you're looking for, but these people have up to 120mm i.d., which seems like it would be plenty big enough:

https://www.eplastics.com/shapes/acetal-delrin/tube
Hank

User avatar
jacquesmm
Site Admin
Site Admin
Posts: 27153
Joined: Wed Aug 14, 2002 1:00 am
Location: Florida USA
Contact:

Re: Corsair 13 in Metairie LA

Post by jacquesmm » Mon Dec 09, 2019 11:57 am

Yes, find a local machine shop that has leftover of Delrin, they"ll know what to do. BTW, Delrin is a name brand. You can use other brands of HD plastic. Technically, it is an acetal sometimes named a POM.

For the wing nut, it's just a large wing nut. Any good size SS wing nut and bolt will do.
Jacques Mertens - Designer
http://bateau.com

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest