Erik and Randy's CX19

Power Boats only. Please include the boat type in your question.
Jeff
Site Admin
Site Admin
Posts: 4815
Joined: Fri Apr 29, 2016 12:17 pm
Location: Vero Beach

Re: Erik and Randy's CX19

Post by Jeff » Thu Mar 14, 2019 2:13 pm

Agree with Dr Pete, you guys are looking really good!! Jeff



randygarst
Frequent Poster
Frequent Poster
Posts: 18
Joined: Fri Dec 14, 2018 1:48 pm
Location: TX

Re: Erik and Randy's CX19

Post by randygarst » Thu Mar 14, 2019 7:15 pm

We added the chine rails and epoxyed those and the strakes today.
P1050515.JPG
P1050515.JPG (131 KiB) Viewed 212 times
P1050512.JPG
P1050512.JPG (131.5 KiB) Viewed 212 times

tonaphun
Frequent Poster
Frequent Poster
Posts: 28
Joined: Fri Jan 04, 2019 5:34 pm
Location: Austin TX

Re: Erik and Randy's CX19

Post by tonaphun » Thu Mar 14, 2019 10:29 pm

Here are some pictures from the end of today. Strakes and Spray rail at chine installed with a coat of epoxy after installation. We still have fillet to be done to fill in the gap and make a nice transition with the hull. We choose to use screws from inside to temporarily clamp them to the hull while the Gel Magic kicks. We will tackle the rub rails tomorrow. It was nice these past two days to add something to the hull and get past the epoxy, sand, tape, sand, glass sand, fair, sand and repeat phase. I know we'll be there again but these two days were fun!
20190314_172343.jpg
20190314_172402.jpg
20190314_172409.jpg
20190314_172432.jpg
20190314_172450.jpg
20190314_172712.jpg

Jeff
Site Admin
Site Admin
Posts: 4815
Joined: Fri Apr 29, 2016 12:17 pm
Location: Vero Beach

Re: Erik and Randy's CX19

Post by Jeff » Fri Mar 15, 2019 7:13 am

tonaphun, really nice progress by you guys!!! Jeff

piperdown
Very Active Poster
Very Active Poster
Posts: 699
Joined: Fri Jun 22, 2018 12:35 pm
Location: Kansas

Re: Erik and Randy's CX19

Post by piperdown » Fri Mar 15, 2019 7:39 am

You guys are doing great!! Boat is looking good :D
Eric (aka, piperdown)

"Give an Irishman lager for a month and he's a dead man. An Irishman's stomach is lined with copper, and the beer corrodes it. But whiskey polishes the copper and is the saving of him." --> Mark Twain

randygarst
Frequent Poster
Frequent Poster
Posts: 18
Joined: Fri Dec 14, 2018 1:48 pm
Location: TX

Re: Erik and Randy's CX19

Post by randygarst » Wed Mar 20, 2019 6:54 pm

Today was our initial epoxy primer day. We used about 5/8 gallon of Pettit High Build Epoxy Primer (white). We have another gallon (gray) which should allow us to have enough left over from the second coat to add a third coat (white/gray mix). Subsequent coats will help us improve our coverage. We expected to expose imperfections but were pleasantly surprised at how few there were. All-in-all it was a good day!
P1050517.JPG
P1050517.JPG (136 KiB) Viewed 127 times
P1050520.JPG
P1050520.JPG (128 KiB) Viewed 127 times
P1050519.JPG
P1050519.JPG (130.5 KiB) Viewed 127 times
P1050518.JPG
P1050518.JPG (142 KiB) Viewed 127 times

User avatar
BB Sig
Very Active Poster
Very Active Poster
Posts: 807
Joined: Thu Sep 29, 2011 9:20 am
Location: Tallahassee, FL
Contact:

Re: Erik and Randy's CX19

Post by BB Sig » Wed Mar 20, 2019 7:25 pm

Great job!

User avatar
jacquesmm
Site Admin
Site Admin
Posts: 26807
Joined: Wed Aug 14, 2002 1:00 am
Location: Florida USA
Contact:

Re: Erik and Randy's CX19

Post by jacquesmm » Wed Mar 20, 2019 8:23 pm

Looks very fair, nice.
Jacques Mertens - Designer
http://bateau.com

Dr. Pete
Frequent Poster
Frequent Poster
Posts: 85
Joined: Sun Jan 22, 2017 6:51 pm
Location: Blanco, Texas

Re: Erik and Randy's CX19

Post by Dr. Pete » Wed Mar 20, 2019 8:38 pm

Aw Hell No. Looks great! Be there for the Port Aransas Plywood Boat Festival and look forward to seeing you guys then. April 12-14. Should be a fun weekend

Jeff
Site Admin
Site Admin
Posts: 4815
Joined: Fri Apr 29, 2016 12:17 pm
Location: Vero Beach

Re: Erik and Randy's CX19

Post by Jeff » Thu Mar 21, 2019 7:56 am

Really well done guys!!! Jeff

Post Reply

Who is online

Users browsing this forum: CatfishHunter and 1 guest