Panga 20 Build

Power Boats only. Please include the boat type in your question.
fallguy1000
Very Active Poster
Very Active Poster
Posts: 5992
Joined: Tue Jan 12, 2010 12:25 am

Re: Panga 20 Build

Post by fallguy1000 » Tue Jan 01, 2019 11:09 am

I use lasers extensively.

Even as a relative, not absolute reference.


My boat build is here -------->

viewtopic.php?f=12&t=62495

FluidDynamic
Active Poster
Active Poster
Posts: 345
Joined: Sun Dec 30, 2018 9:09 pm
Location: Spanish Fort, AL

Re: Panga 20 Build

Post by FluidDynamic » Tue Jan 01, 2019 11:38 am

Station C is in.
there's nothing like the feeling when a boat starts to take shape.
Attachments
IMG_20190101_103358.jpg
IMG_20190101_103346.jpg

fallguy1000
Very Active Poster
Very Active Poster
Posts: 5992
Joined: Tue Jan 12, 2010 12:25 am

Re: Panga 20 Build

Post by fallguy1000 » Tue Jan 01, 2019 11:49 am

Did you tapcon the 2x chuncks to the floor? It looked like nails, but also saw washers, so might be my eyes is all.

You don't want the strongback to move.

When I setup the cnc'd frames for my cat build, it took awhile for me to realize a bevel was required in the front sections to avoid a wave in the hull. I used a 22 degree cutting head with a flush bearing. Had to add a piece temp for the bearing to ride iirc or I bumped the top edge woth bearing? But just a heads up for you to remember.

Your plans might even advise.
My boat build is here -------->

viewtopic.php?f=12&t=62495

FluidDynamic
Active Poster
Active Poster
Posts: 345
Joined: Sun Dec 30, 2018 9:09 pm
Location: Spanish Fort, AL

Re: Panga 20 Build

Post by FluidDynamic » Tue Jan 01, 2019 12:28 pm

They are ramset nails that were shot into the concrete. Should anchor with bolts instead?
Last edited by FluidDynamic on Tue Jan 01, 2019 4:46 pm, edited 3 times in total.

fallguy1000
Very Active Poster
Very Active Poster
Posts: 5992
Joined: Tue Jan 12, 2010 12:25 am

Re: Panga 20 Build

Post by fallguy1000 » Tue Jan 01, 2019 12:37 pm

Just make sure they aren't loose. Ramsets should be fine.
My boat build is here -------->

viewtopic.php?f=12&t=62495

FluidDynamic
Active Poster
Active Poster
Posts: 345
Joined: Sun Dec 30, 2018 9:09 pm
Location: Spanish Fort, AL

Re: Panga 20 Build

Post by FluidDynamic » Tue Jan 01, 2019 1:37 pm

FluidDynamic wrote:
Tue Jan 01, 2019 12:28 pm
They are ramset nails that were shot into the ground. Should anchor with bolts instead?

FluidDynamic
Active Poster
Active Poster
Posts: 345
Joined: Sun Dec 30, 2018 9:09 pm
Location: Spanish Fort, AL

Re: Panga 20 Build

Post by FluidDynamic » Tue Jan 01, 2019 4:45 pm

FluidDynamic wrote:
Tue Jan 01, 2019 12:28 pm
They are ramset nails that were shot into the concrete. Should anchor with boots instead?

FluidDynamic
Active Poster
Active Poster
Posts: 345
Joined: Sun Dec 30, 2018 9:09 pm
Location: Spanish Fort, AL

Re: Panga 20 Build

Post by FluidDynamic » Tue Jan 01, 2019 11:38 pm

I've been reading Jasmine and Dynamos panga 20 builds and have a question about bending the bottom around the frames. It looks like they used Meranti for there bottom panels. If I'm using Okoume, will I have as much trouble as they did?

User avatar
OrangeQuest
Very Active Poster
Very Active Poster
Posts: 3195
Joined: Tue Aug 28, 2018 1:14 pm
Location: Houston, Texas

Re: Panga 20 Build

Post by OrangeQuest » Wed Jan 02, 2019 5:32 am

Okoume bends easier than Meranti.
"that it isn't just an ordinary sort of boat. Sometimes it's a Boat, and sometimes it's more of an Accident. It all depends." "Depends on what?" "On whether I'm on the top of it or underneath it."
A. A. Milne

Jeff
Site Admin
Site Admin
Posts: 6723
Joined: Fri Apr 29, 2016 12:17 pm
Location: Vero Beach

Re: Panga 20 Build

Post by Jeff » Wed Jan 02, 2019 8:19 am

FluidDynamic, OQ is absolutely correct!! Okoume BS1088 is a lighter and easier to bend & shape!!! Jeff

Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests